Subscribe

Sign up for free

  • Get quick access to your favorite articles

  • Manage alerts on breaking news and favorite drivers

  • Make your voice heard with article commenting.

Autosport Plus

Discover premium content
Subscribe

How F1 teams are changing cars without new parts

Formula 1's cost cap rules are forcing teams to change their approach to car improvement, as they look for ways to improve performance without the need for new parts.

George Russell, Mercedes F1 W14

George Russell, Mercedes F1 W14

Steve Etherington / Motorsport Images

Giorgio Piola's F1 technical analysis

Giorgio Piola is the preeminent Formula 1 technical journalist. Born in Genoa, Italy, Giorgio has covered the F1 World Championship since 1969, producing thousands of illustrations that have been reproduced in the world’s most prestigious motor racing publications.

A case in point was spotted in Miami last weekend as both Mercedes and Williams took to free practice with different configurations mounted on their cars.

Mercedes W14 comparison - Miami

Mercedes W14 comparison - Miami

Photo by: Uncredited

For Mercedes, this resulted in Lewis Hamilton running with an infill panel for the upper tip section of the rear wing endplate. Meanwhile, George Russell utilised a more conventional cut-out.

This design difference has a marked effect on the behaviour of the outer section of the wing, with drag and downforce levels traded off against one another.

This sort of experimentation is helped by Mercedes' decision to produce a rear wing that has interchangeable parts, which not only saves money in terms of manufacturing but also allows for quick aerodynamic setup changes too (red arrow).

Meanwhile, at the front of the car, Mercedes trimmed the inboard trailing edge of the upper flap in a crescent shape to help reduce downforce and balance the car with its choices at the rear of the car (blue arrow).

This is a solution that we first saw from Alpine in Azerbaijan, as it also looked to find the right balance front-to-rear.

For qualifying and the race, Hamilton continued with the arrangement seen above, while Russell made the switch to the front wing with the cut-out but retained the rear wing tip cut-out.

More, or less?

Williams FW45 rear and beam wing comparison - Miami

Williams FW45 rear and beam wing comparison - Miami

Photo by: Uncredited

Williams was also experimenting with its aerodynamic setup during free practice, as it looked at ways to trade performance between the upper rear wing elements and the beam wing.

Alex Albon was tasked with trialling the higher downforce rear wing arrangement with just a single lower beam wing element, while Logan Sargeant ran laps with the lower downforce rear wing, which was married to a double beam wing set-up.

In the end, Sargeant switched out to the same arrangement as Albon, as the team leaned on more performance from the rear wing, while improving its straightline speed with the single beam wing element.

Cooling off period…

Aston Martin AMR23 cooling panel options

Aston Martin AMR23 cooling panel options

Photo by: Uncredited

Aston Martin added another cooling option in the engine cover panel to help deal with the demands of the Miami street circuit.

The team has various options available, including bodywork panels where the louvres are pitched more open and closed, while longer and shorter blanking panels are also possible in order to help trade cooling/heat rejection for aerodynamic efficiency and vice versa.

Red Bull RB19 asymmetric engine cover cooling

Red Bull RB19 asymmetric engine cover cooling

Photo by: Uncredited

Meanwhile, Red Bull has taken to running with an asymmetric cooling configuration on the RB19 this season, with the team once again opting for the louvred cooling panel to be used on just the right-hand side of the car in Miami (red arrow).

It also toyed with a couple of options for more or less cooling during free practice, before settling on the more expansive option for the race and qualifying (lower, larger inset).

Ferrari SF-23 outer floor and fence comparison (highlighted)

Ferrari SF-23 outer floor and fence comparison (highlighted)

Photo by: Uncredited

Ferrari is set to introduce a raft of new parts for the SF-23 in the upcoming races, as it looks to close the gap to Red Bull ahead of it.

It kicked this off in Miami as a new floor arrived that featured numerous changes up and down the assembly to provide a performance boost across the spectrum, rather than just providing a singular focus.

The outer front section of the floor and the shape of the outer fence have been modified, with a more pronounced bulge present in the forward section of the downward ramp section of the floor (see yellow highlights), while the shape and height of the trailing edge of the floor fence ahead of it has also been altered as a consequence.

The change in curvature will have an impact on the airflow's behaviour on the top surface but, perhaps more critically, it will change the available pocket of space in the underfloor beneath, with the shape of the floor fences also likely optimised in order to further enhance the effect.

Ferrari SF-23 floor detail

Ferrari SF-23 floor detail

Photo by: Giorgio Piola

There also appear to have been some subtle changes to the various surface contours used on the floor's edge, with the upwardly rolled scroll section and the section that tapers toward the rear tyre both subtly different in Miami.

There were also changes in the diffuser, as the team modified the shape of the central boat tail section, in order to take advantage of the advancements made ahead of it.

Ferrari SF-23 rear detail

Ferrari SF-23 rear detail

Photo by: Giorgio Piola

Be part of the Autosport community

Join the conversation
Previous article Alpine plans F1 recruitment drive, investment and new simulator
Next article Albon explains angry F1 radio messages during Miami GP

Top Comments

There are no comments at the moment. Would you like to write one?

Sign up for free

  • Get quick access to your favorite articles

  • Manage alerts on breaking news and favorite drivers

  • Make your voice heard with article commenting.

Autosport Plus

Discover premium content
Subscribe